Electric hot water boiler Boiler 100L 2kW

The set contains elements that ensure a comfortable and correct installation of the heater Product features The set contains elements that ensure a comfortable and correct installation of the heater Included in the set: solid support cable with plug, safety valve, assembly and use instructions, warranty card The installation of the heater should be selected by the installer according to the type of wall on which the boiler is to be installed The heaters of the Standard Plus series are equipped with a high-efficiency electric copper heater with a power of 2 kW, which gives the device a gives high efficiency This results in a short hot water production time and compromises the high level of comfort when using the boiler The boilers have a thermostat with external temperature control located at the bottom of the housing The unique ANTIMIX system prevents the layers of cold and heated water from mixing This results in higher hot water efficiency and prevents sudden temperature changes SAVE Thanks to the improved polyurethane insulation that limits heat loss, NOVA consumes up to 30% less Electricity Polyurethane has a low thermal conductivity coefficient and is therefore a very good heat insulator. Due to the high insulating properties of the material, polyurethane can be used to create thinner and therefore lighter and easier to apply thermal insulation layers. SAFETY Two temperature sensors prevent overheating and a safety valve protects the device from excessive water pressure. The safety valve opens when the pressure in the device is too high. This reduces the pressure in the water heater., The magnesium anode is a very important element of the water heater and protects it from rust in the tank This protects the boiler from corrosion, which could lead to leaks in the tank coating Legionella removal function Thanks to the possibility of heating water to a maximum temperature of 77 ° C, we can remove harmful Legionella bacteria (if any) at any time We carry out thermal disinfection ourselves by setting the highest temperature and holding it for at least 2 minutes. After this time, the bacteria die and the boiler is completely disinfected MODERN SOLUTIONS The function of two tanks (which increases the production cost of the device and therefore the final price for the customer) is replaced in NovaTec tanks by the Antimix system, which ensures rapid heating of the water to maximize the comfort of using the boiler The unique ANTIMIX system prevents the layers of cold and already heated water from mixing This increases the efficiency of hot water and avoids sudden temperature changes The ANTICALC system significantly extends the life of the boiler and makes it easier the cleaning GOOD QUALITY The water heater is made of high quality steel and additionally enamelled This is the best protection against corrosion The enamel used contains titanium, which makes it flexible and resistant to changing internal conditions that arise when filling the tank with cold water and subsequent heating This design and solutions also protect against the negative effects of very hard water and allow long-term preservation of technical, ecological and hygienic properties The heating element is made of corrosion-resistant copper, which is characterized by a high Thermal conductivity coefficients Copper is a noble metal with biostatic properties, that is, it inhibits the growth of batteries in the tank Steel heaters do not offer these advantages EASY TO USE No specialist knowledge is required for installation and the product is ready to install The external temperature control allows you to change the temperature settings conveniently and easily ACTIVE ELECTRICAL PROTECTION FUNCTION Once the heating process is complete, the heater is completely disconnected from the mains to ensure maximum safety OVERHEAT PROTECTION SYSTEM In the event of component failure, the heater switches off to prevent overheating of the water and possible scalding DURABILITY The production quality control system guarantees the longevity of each device SPACE SAVING When wall mounted, the vertical model takes up minimal space in the room NO HEAT BRIDGE The high-performance polyurethane insulation keeps the water warm until use, eliminating the thermal bridge between the water tank and the mounting bracket This results to lower heat losses, which significantly improves the operating comfort of the device. Characteristic: Housing made of durable epoxy resin Cover for shockproof temperature display Triple security system Enlarged magnesium anode Reinforced polyurethane thermal insulation Unique patented antibacterial surface. 100% quality control of the internal coating of the tank Heating temperature regulation Service on the territory of the Republic of Poland The cable ends with einem 230-V-Stecker Capacity: 100 liters Voltage: 230 V Electrical power: 2000 W Mounting type: vertical Nominal pressure: 0.6 MPa Protection class: I Protection class: IP24 Heating time from 15°C to 65°C: 177 min Water heating temperature: 77°C Corrosion protection: Magnesium anode material: enameled steel (S235JR)